Printed on high quality paper, and durably bound, this standard is approved for use by all Departments and Agencies of the Department of Defense. This standard establishes general human engineering criteria for design and development of military systems, equipment, and facilities. Human engineering is one of seven domains of Human-systems integration (as defined in the DoD 5000 series) and is synonymous with Human factors engineering. The purpose of this standard is to present human engineering design criteria, principles, and practices to be applied in the design of systems, equipment, and facilities so as to: a. Achieve required performance by operator, control, and maintenance personnel. b. Achieve required manpower readiness for system performance. c. Achieve required reliability of personnel-equipment combinations. d. Foster design standardization within and among systems. This standard does not alter requirements for system development participation of human engineering specialists to interpret and implement these practices and to provide solutions to human engineering problems which arise and which are not specifically covered herein. Requirements herein are expressed in the International System of Units (SI). As a convenience, the metric units are accompanied by their approximate customary system equivalents (in parentheses). Angular measure is expressed in degrees unless it is necessary to specify fractions of a degree where milliradians are used. MIL-STD-1472 has not had a thorough technical review since the late 1980s. MIL-STD-1472D was promulgated in March 1989, and hence addressed the level of technology that existed through 1988 or possibly 1987. The “E” revision, promulgated in 1996, was mostly cosmetic; the text was changed to a non-proportional font in order to reduce white space. The “F” revision, promulgated in 1999, consisted mainly of moving the anthropometric data from MIL-STD-1472 to MIL-HDBK-759, but little else. As a result, requirements and design criteria contained in previous versions of MIL-STD-1472 may no longer be applicable to today's technology. The operational benefits of emerging technologies may be limited due to the out-of-date design criteria. Tomorrow's systems will depend on greater cognitive processing on the part of the human operator, maintainer, and support personnel. Portable or wearable computers are likely to be commonplace. New display concepts such as virtual reality, haptic (touch sensing), and three-dimensional are receiving a great deal of interest, as are voice, pointing, gesture, and eye-blink control systems. Technology, if misapplied, will impose human performance requirements that cannot be satisfied. Many technologies are evolving rapidly; the human is not. The benefits of new technologies may not be realized if one fails to consider human capabilities and limitations. The changes made in the “G” revision over the previous version are substantial. The organizational structure of the standard was revamped to group similar material in the same section of the document. Obsolete provisions (e.g., reference to dot-matrix printers) were deleted, out-of-date provisions were updated to reflect the latest research, and new provisions were added to address emerging technologies. See 6.4 for a summary of changes to the present “G” revision.

The purpose of this handbook is to provide guidance in the application of human engineering to the design and development of management information (and related) software systems. The users of this document are intended to be any individual, or group, who participates in the development of software systems, including logicians, software engineers, end-system users, software development managers, programmers, system evaluators, and human factors engineers. This handbook provides analysis techniques and methodologies for management information system development and presents human engineering guidelines for detailed user-computer interface software design. Where hardware design guidance is needed, the requirements of MIL-STD-1472 'Human Engineering Design Criteria for Military Systems, Equipment, and Facilities' should apply.

This digest was prepared by the Human Factors Standardization SubTAG of the Department of Defense Human Factors Engineering Technical Advisory Group (DoD HFE TAG).This booklet is a digest of material appearing in MIL-STD-1472, and is complemented with material from MIL-HDBK-759 and the Federal Aviation Administration (FAA) Human Factors Design Guide. The user is therefore referred to those documents and its references for required supplementary information.This digest provides basic, quantitative human engineering design data in pictorial, tabular, and graphical formats for use during system, equipment, or facility design and assessment. Its purpose is to furnish a convenient “portable” reference of human engineering design criteria and guidelines. The principles, explanations, limitations, and application techniques associated with the data have been intentionally omitted. This abbreviated presentation presupposes that the user is familiar with the bases and limitations of the given data or will consult applicable references to ensure appropriate application of the data.

How to design for optimum maintenance capabilities and minimize the repair time Design for Maintainability offers engineers a wide range of tools and techniques for incorporating maintainability into the design process for complex systems. With contributions from noted experts on the topic, the book explains how to design for optimum maintenance capabilities while simultaneously minimizing the time to repair equipment. The book contains a wealth of examples and the most up-to-date maintainability design practices that have proven to result in better system readiness, shorter downtimes, and substantial cost savings over the entire system life cycle, thereby, decreasing the Total Cost of Ownership. Design for Maintainability offers a wealth of design practices not covered in typical engineering books, thus allowing readers to think outside the box when developing maintainability design requirements. The books principles and practices can help engineers to dramatically improve their ability to compete in global markets and gain widespread customer satisfaction. This important book: Offers a complete overview of maintainability engineering as a system engineering discipline Includes contributions from authors who are recognized leaders in the field Contains real-life design examples, both good and bad, from various industries Presents realistic illustrations of good maintainability design principles Provides discussion of the interrelationships between maintainability with other related disciplines Explores trending topics in technologies Written for design and logistics engineers and managers, Design for Maintainability is a comprehensive resource containing the most reliable and innovative techniques for improving maintainability when designing a system or product.