We present a measurement of the top quark pair production cross section in p{bar p} collisions at √s = 1.96 TeV using approximately 1 fb−1 of data collected with the D0 detector. We consider decay channels containing two high p{sub T} charged leptons where one lepton is identified as an electron or a muon while the other lepton can be an electron, a muon or a hadronically decaying [tau] lepton. For a mass of the top quark of 170 GeV, the measured cross section is 7.5{sub -1.0}{sup +1.0}(stat){sub -0.06}{sup +0.7}(syst){sub -0.5}{sup 0.6}(lumi) pb. Using l{sub {tau}} events only, they measure: [sigma]{sub t{bar t}} x B(t{bar t} → l{sub {tau}}b{bar b}) = 0.13{sub -0.08}{sup +0.09}(stat){sub -0.06}{sup 0.06}(syst)+{sub -0.02}{sup +0.02}(lumi) pb. Comparing the measured cross section as a function of the mass of the top quark with a partial next-to-next-to leading order Quantum Chromodynamics theoretical prediction, we extract a mass of the top quark of 171.5{sub -8.8}{sup +9.9} GeV, in agreement with direct measurements.

We present a measurement of the top quark pair (t{bar t}) production cross section ([sigma]{sub t{bar t}}) in p{bar p} collisions at a center-of-mass energy of 1.96 TeV using 230 pb1 of data collected by the D0 detector at the Fermilab Tevatron Collider. We select events with one charged lepton (electron or muon), large missing transverse energy, and at least four jets, and extract the t{bar t} content of the sample based on the kinematic characteristics of the events. For a top quark mass of 175 GeV, we measure [sigma]{sub t{bar t}} = 6.7{sub -1.3}{sup +1.4}(stat){sub -1.1}{sup +1.6}(syst) ± 0.4(lumi)pb, in good agreement with the standard model prediction.

We present a measurement of the top quark pair production cross section in p{bar p} collisions at √s = 1.96 TeV utilizing 425 pb−1 of data collected with the D0 detector at the Fermilab Tevatron Collider. We consider the final state of the top quark pair containing one high-p{sub T} electron or muon and at least four jets. We exploit specific kinematic features of t{bar t} events to extract the cross section. For a top quark mass of 175 GeV, we measure?{sub t{bar t}} = 6.4{sub -1.2}{sup +1.3}(stat) ± 0.7(syst) ± 0.4(lum)pb, in good agreement with the standard model prediction.

Before any kind of new physics discovery could be made at the LHC, a precise understanding and measurement of the Standard Model of particle physics' processes was necessary. The book provides an introduction to top quark production in the context of the Standard Model and presents two such precise measurements of the production of top quark pairs in proton-proton collisions at a center-of-mass energy of 7 TeV that were observed with the ATLAS Experiment at the LHC. The presented measurements focus on events with one charged lepton, missing transverse energy and jets. Using novel and advanced analysis techniques as well as a good understanding of the detector, they constitute the most precise measurements of the quantity at that time.

This paper reports a measurement of the cross section for the pair production of top quarks in p{bar p} collisions at √s = 1.96 TeV at the Fermilab Tevatron. The data was collected from the CDF II detector in a set of runs with a total integrated luminosity of 1.1 fb−1. The cross section is measured in the dilepton channel, the subset of t{bar t} events in which both top quarks decay through t → Wb → l?b, where l = e,?, or?. The lepton pair is reconstructed as one identified electron or muon and one isolated track. The use of an isolated track to identify the second lepton increases the t{bar t} acceptance, particularly for the case in which one W decays as W →??. The purity of the sample may be further improved at the cost of a reduction in the number of signal events, by requiring an identified b-jet. They present the results of measurements performed with and without the request of an identified b-jet. the former is the first published CDF result for which a b-jet requirement is added to the dilepton selection. In the CDF data there are 129 pretag lepton + track candidate events, of which 69 are tagged. With the tagging information, the sample is divided into tagged and untagged sub-samples, and a combined cross section is calculated by maximizing a likelihood. The result is?{sub t{bar t}} = 9.6 ± 1.2(stat.){sub -0.5}{sup +0.6}(sys.) ± 0.6(lum.) pb, assuming a branching ratio of BR(W → l?) = 10.8% and a top mass of m{sub t} = 175 GeV/c2.

This paper reports a measurement of the cross section for the pair production of top quarks in p{bar p} collisions at √s = 1.96 TeV at the Fermilab Tevatron. The data was collected from the CDF II detector in a set of runs with a total integrated luminosity of 1.1 fb−1. The cross section is measured in the dilepton channel, the subset of t{bar t} events in which both top quarks decay through t → Wb → l[nu]b, where l = e, [mu], or [tau]. The lepton pair is reconstructed as one identified electron or muon and one isolated track. The use of an isolated track to identify the second lepton increases the t{bar t} acceptance, particularly for the case in which one W decays as W → [tau][nu]. The purity of the sample may be further improved at the cost of a reduction in the number of signal events, by requiring an identified b-jet. They present the results of measurements performed with and without the request of an identified b-jet. the former is the first published CDF result for which a b-jet requirement is added to the dilepton selection. In the CDF data there are 129 pretag lepton + track candidate events, of which 69 are tagged. With the tagging information, the sample is divided into tagged and untagged sub-samples, and a combined cross section is calculated by maximizing a likelihood. The result is [sigma]{sub t{bar t}} = 9.6 ± 1.2(stat.){sub -0.5}{sup +0.6}(sys.) ± 0.6(lum.) pb, assuming a branching ratio of BR(W → l[nu]) = 10.8% and a top mass of m{sub t} = 175 GeV/c2.