Explaining the principles that underlie strong ground motion simulation, this publication describes various methods for simulating strong ground motions, and presents some examples of strong ground motion simulations using fault rupture modelling. The detailed guidelines and practical tools presented in this Safety Report will be of value to researchers, operating organizations, regulatory bodies, vendors and technical support organizations in the areas of seismic hazard evaluation of nuclear installations. The information provided will also be of great importance for seismic hazard assessments following the Fukushima Daiichi nuclear power plant accident.

This volume collects several extended articles from the first workshop on Best Practices in Physics-based Fault Rupture Models for Seismic Hazard Assessment of Nuclear Installations (BestPSHANI). Held in 2015, the workshop was organized by the IAEA to disseminate the use of physics-based fault-rupture models for ground motion prediction in seismic hazard assessments (SHA). The book also presents a number of new contributions on topics ranging from the seismological aspects of earthquake cycle simulations for source scaling evaluation, seismic source characterization, source inversion and physics-based ground motion modeling to engineering applications of simulated ground motion for the analysis of seismic response of structures. Further, it includes papers describing current practices for assessing seismic hazard in terms of nuclear safety in low seismicity areas, and proposals for physics-based hazard assessment for critical structures near large earthquakes. The papers validate and verify the models by comparing synthetic results with observed data and empirical models. The book is a valuable resource for scientists, engineers, students and practitioners involved in all aspects of SHA.

This Safety Guide supersedes the 2010 edition of IAEA Safety Standards Series No. SSG-9. It takes account of recently gained knowledge and practices developed by Member States related to seismic hazards, especially lessons from the Fukushima Daiichi accident. It also addresses concomitant events associated with earthquakes, such as tsunamis. The revision provides a clearer separation between the process for assessing the seismic hazards at a specific nuclear installation site and the process for defining the related basis for design and safety assessment of the nuclear installation. Thus, it bridges gaps and avoids undue overlap of the two processes, which correspond to and are performed at different stages of siting of the nuclear installation.

This volume collects several extended articles from the first workshop on Best Practices in Physics-based Fault Rupture Models for Seismic Hazard Assessment of Nuclear Installations (BestPSHANI). Held in 2015, the workshop was organized by the IAEA to disseminate the use of physics-based fault-rupture models for ground motion prediction in seismic hazard assessments (SHA). The book also presents a number of new contributions on topics ranging from the seismological aspects of earthquake cycle simulations for source scaling evaluation, seismic source characterization, source inversion and physics-based ground motion modeling to engineering applications of simulated ground motion for the analysis of seismic response of structures. Further, it includes papers describing current practices for assessing seismic hazard in terms of nuclear safety in low seismicity areas, and proposals for physics-based hazard assessment for critical structures near large earthquakes. The papers validate and verify the models by comparing synthetic results with observed data and empirical models. The book is a valuable resource for scientists, engineers, students and practitioners involved in all aspects of SHA.

This book is a comprehensive compilation of earthquake- and tsunami-related technologies and knowledge for the design and construction of nuclear facilities. As such, it covers a wide range of fields including civil engineering, architecture, geotechnical engineering, mechanical engineering, and nuclear engineering, for the development of new technologies providing greater resistance against earthquakes and tsunamis. It is crucial both for students of nuclear energy courses and for young engineers in nuclear power generation industries to understand the basics and principles of earthquake- and tsunami-resistant design of nuclear facilities. In Part I, "Seismic Design of Nuclear Power Plants", the design of nuclear power plants to withstand earthquakes and tsunamis is explained, focusing on buildings, equipment's, and civil engineering structures. In Part II, "Basics of Earthquake Engineering", fundamental knowledge of earthquakes and tsunamis as well as the dynamic response of structures and foundation ground are explained.

Engineers use earthquake ground motions for a variety of reasons, including seismic hazard assessment, calibration of ground motion prediction equations (GMPEs), and input to nonlinear response history analysis. These analyses require a significant number of ground motions and for some scenarios, such as earthquakes with large magnitudes and short distances, it may be difficult to obtain a sufficient number of ground motion recordings. When sufficient recordings do not exist, engineers modify available recordings using scaling or spectrum matching, or they use ground motion simulations. Ground motion simulations have existed for decades, but recent advances in simulation methods due to improved source characterization and wave propagation, coupled with increased computing power, have increased potential benefits for engineers. But before simulations can be used in engineering applications, simulations must be accessible and consistent with natural observations. This dissertation contributes to the latter issue, and it investigates the application of simulations to specific engineering problems. The Southern California Earthquake Center (SCEC) Broadband Platform (BBP) is an open-source software distribution that enables third-party users to simulate ground motions using research code contributed by model developers. Because the BBP allows users to compute their own simulations with little knowledge of the underlying implementation and it ensures that all calculations are reproducible, it is extremely valuable for simulation validation and engineering applications. In this dissertation, the BBP is evaluated as a simulation generation tool from an engineering perspective. Ground motions are simulated to study parameters of engineering interest, such as high-frequency variability, near-fault ground motions, and local site response. Though some parameters need further development, such as site response (which is currently implemented using simple empirical amplification), the BBP proves to be an effective tool for facilitating these types of engineering studies. This dissertation proposes a simulation validation framework based on simple and robust proxies for the response of more complicated structures. We compile a list of proxies with robust empirical models that are insensitive to changes in earthquake scenario and do not rely on extrapolation for rarely observed events. Because predictions of these proxies are reliable under a variety of earthquake events, we can confidently compare them with simulations. The proposed proxies include correlation of epsilon across periods, ratio of maximum to median response across horizontal orientations, and ratio of inelastic to elastic displacement. The validation framework is applied to example simulations and successfully exposes some parameters that need work, such as variability and correlation of spectral acceleration. Finally, this dissertation investigates the application of simulations to response history analysis and fling-step characterization. A 3D nonlinear structural model is analyzed using recordings and simulations with similar elastic response spectra. The structural performance and resulting design decisions are similar, indicating that simulations are effective for response history analysis subject to certain conditions. To investigate fling-step, we extract fling pulses from a large set of simulations. Extracted fling properties such as amplitude and period are then compared to specially-processed recordings and relevant empirical models for surface displacement and pulse period. Reasonably good agreement is found between simulations, recordings, and empirical models. In general, ground motion simulations are found to be an effective alternative or supplement to recordings in several engineering applications. Because simulation methods are still developing, this work is not intended as an evaluation of existing methods, but rather as a development of procedures that can be used in ongoing work.

Earthquake Geotechnical Engineering for Protection and Development of Environment and Constructions contains invited, keynote and theme lectures and regular papers presented at the 7th International Conference on Earthquake Geotechnical Engineering (Rome, Italy, 17-20 June 2019. The contributions deal with recent developments and advancements as well as case histories, field monitoring, experimental characterization, physical and analytical modelling, and applications related to the variety of environmental phenomena induced by earthquakes in soils and their effects on engineered systems interacting with them. The book is divided in the sections below: Invited papers Keynote papers Theme lectures Special Session on Large Scale Testing Special Session on Liquefact Projects Special Session on Lessons learned from recent earthquakes Special Session on the Central Italy earthquake Regular papers Earthquake Geotechnical Engineering for Protection and Development of Environment and Constructions provides a significant up-to-date collection of recent experiences and developments, and aims at engineers, geologists and seismologists, consultants, public and private contractors, local national and international authorities, and to all those involved in research and practice related to Earthquake Geotechnical Engineering.