The book presents laboratory experiments concerning ARM microcontrollers, and discusses the architecture of the Tiva Cortex-M4 ARM microcontrollers from Texas Instruments, describing various ways of programming them. Given the meager peripherals and sensors available on the kit, the authors describe the design of Padma – a circuit board with a large set of peripherals and sensors that connects to the Tiva Launchpad and exploits the Tiva microcontroller family’s on-chip features. ARM microcontrollers, which are classified as 32-bit devices, are currently the most popular of all microcontrollers. They cover a wide range of applications that extend from traditional 8-bit devices to 32-bit devices. Of the various ARM subfamilies, Cortex-M4 is a middle-level microcontroller that lends itself well to data acquisition and control as well as digital signal manipulation applications. Given the prominence of ARM microcontrollers, it is important that they should be incorporated in academic curriculums. However, there is a lack of up-to-date teaching material – textbooks and comprehensive laboratory manuals. In this book each of the microcontroller’s resources – digital input and output, timers and counters, serial communication channels, analog-to-digital conversion, interrupt structure and power management features – are addressed in a set of more than 70 experiments to help teach a full semester course on these microcontrollers. Beyond these physical interfacing exercises, it describes an inexpensive BoB (break out board) that allows students to learn how to design and build standalone projects, as well a number of illustrative projects.

1) Our ARM book series The ARM CPU is licensed and produced by hundreds of companies. The ARM Assembly language instructions and architectures are standardized and all the licensees must follow them. The first volume of this series (ARM Assembly Language Programming & Architecture by Mazidi & Naimi) covers the Assembly language programming, instructions, and architecture of the ARM and can be used with any ARM chip, regardless of the chip maker. Since the licensees are free to design and implement their own peripherals, the peripherals of ARM chips vary greatly among the licensees. For this reason, we have dedicated a separate volume to each licensee. This volume covers the peripheral programming of Texas Instruments (TI) ARM Tiva C series. Throughout the book, we use C language to program the Tiva C Series TM4C123G chip peripherals. We use TM4C123G LaunchPad(TM) Evaluation Kit which is based on ARM(R) Cortex(R)-M4F MCU. See our website for tutorials and support materials: http: //www.MicroDigitalEd.com/ARM/TI_ARM_books.htm 2) Who will use our ARM textbooks? The primary audience of our textbook on ARM is undergraduate and graduate engineering students in Electrical and Computer Engineering departments. We assume no background in microcontroller and embedded systems programming. It can also be used by embedded system programmers who want to move away from 8- and 16-bit legacy chips such as the 8051, AVR, PIC, and HCS08/12 family of microcontrollers to ARM. Designers of the x86-based systems wanting to design ARM-based embedded systems can also benefit from this series. See our website for other titles for ARM Programming and Embedded Systems: http: //www.MicroDigitalEd.com/ARM/ARM_books.htm

Stellaris LM4F120 and Tiva C Series LaunchPad is great products based ARM Cortex-M for learning. This book helps you to get started with Stellaris LM4F120 and Tiva C Series LaunchPad and how to build programs using Energia and Code Composer Studio. The following is highlight topics: * Preparing Development Environment * Developing program using Energia * Developing program using Code Composer Studio 6.x * Accessing board through GPIO, Analog I/O, UART, I2C, and SPI * Providing several code samples to demonstrate how to work

Delivering a solid introduction to assembly language and embedded systems, ARM Assembly Language: Fundamentals and Techniques, Second Edition continues to support the popular ARM7TDMI, but also addresses the latest architectures from ARM, including Cortex-A, Cortex-R, and Cortex-M processors-all of which have slightly different instruction sets, p

Using FreeRTOS and libopencm3 instead of the Arduino software environment, this book will help you develop multi-tasking applications that go beyond Arduino norms. In addition to the usual peripherals found in the typical Arduino device, the STM32 device includes a USB controller, RTC (Real Time Clock), DMA (Direct Memory Access controller), CAN bus and more. Each chapter contains clear explanations of the STM32 hardware capabilities to help get you started with the device, including GPIO and several other ST Microelectronics peripherals like USB and CAN bus controller. You’ll learn how to download and set up the libopencm3 + FreeRTOS development environment, using GCC. With everything set up, you’ll leverage FreeRTOS to create tasks, queues, and mutexes. You’ll also learn to work with the I2C bus to add GPIO using the PCF8574 chip. And how to create PWM output for RC control using hardware timers. You'll be introduced to new concepts that are necessary to master the STM32, such as how to extend code with GCC overlays using an external Winbond ​W25Q32 flash chip. Your knowledge is tested at the end of each chapter with exercises. Upon completing this book, you’ll be ready to work with any of the devices in the STM32 family. Beginning STM32 provides the professional, student, or hobbyist a way to learn about ARM without costing an arm! What You'll Learn Initialize and use the libopencm3 drivers and handle interrupts Use DMA to drive a SPI based OLED displaying an analog meter Read PWM from an RC control using hardware timers Who This Book Is For Experienced embedded engineers, students, hobbyists and makers wishing to explore the ARM architecture, going beyond Arduino limits.