The Zircaloy cladding of water reactor fuel rods is susceptible to local breach-type failure, commonly known as pellet-cladding interaction (PCI) failure, during operational and off-normal power transients after the fuel has achieved a sufficiently high burnup. An optimization of power ramp procedures or fuel rod fabrication to minimize the cladding failure would result in a significant decrease in radiation exposure of plant personnel due to background and airborne radioactivity as well as an extension of core life in terms of allowable off-gas radioactivity. As part of a program to provide a better understanding of the fuel rod faiure phenomenon and to facilitate the formulation of a better failure criterion, a mechanistic study of the deformation and fracture behavior of high-burnup spent-fuel cladding is in progress under simulated PCI conditions.

For a better understanding of Zircaloy fuel-rod failure by the pellet-cladding interaction (PCI) phenomenon, a mechanistic study of deformation and fracture behavior of spent power reactor fuel cladding under simulated PCI conditions was conducted. Zircaloy-2 cladding specimens, obtained from fuel assemblies of operating power reactors, were deformed to fracture at 325°C by internal gas pressurization in the absence of fission product simulants. Fracture characteristics and microstructures were examined via SEM, TEM, and HVEM. Numerous dislocation tangles and cell structures, observed in TEM specimens of cladding tubes that failed in a ductile manner, were consistent with SEM observations of a limited number of dimples characteristic of microvoid coalescence. A number of brittle-type failures were produced without the influence of fission product simulants. The brittle cracks occurred near the areas compressed by the Swagelok fittings of the internally pressurized tube and propagated from the outer to the inner surface. Since the outer surface was isolated and maintained under a flowing stream of pure helium, it is unlikely that the brittle-type failure was influenced by any fission product traces. SEM fractography of the brittle-type failure revealed a large area of transgranular pseudocleavage with limited areas of ductile fluting, which were similar in appearance to the surfaces produced by in-reactor PCI-type failures. A TEM evaluation of the cladding in the vicinity of the through-wall crack revealed numerous locations that contained an extensive amount of second-phase precipitate (Zr3O). We believe that the brittle-type failures of the irradiated spent fuel cladding in the stress rupture experiments are associated with segregation of oxygen, which leads to the formation of the order structure, an immobilization of dislocations, and minimal plastic deformation in the material.

PCI-like, brittle-type failures, characterized by pseudocleavage-plus-fluting features in the fracture surface, branching cracks, and small diametral strain, were observed to occur at 292 to 325°C in some batches of spent power-reactor fuel-cladding tubes under internal gas-pressurization and expanding-mandrel loading conditions in which the tests were not influenced by fission product simulants. Fractographic characteristics per se do not provide evidence for a PCI failure mechanism but should be deemed only as cooroborative in nature. Evaluation of TEM thin-foil specimens, obtained from regions adjacent to the brittle-type fracture sites, characteristically revealed extensive amounts of Zr3O precipitates and a lack of slip dislocations. The precipitation of the Zr3O phase appears to be enhanced by a high density of irradiation-induced defects. The brittle-type failure produced in the spent-fuel cladding tubes appears to be associated with segregation of oxygen to dislocation substructures and irradiation-induced defects, which leads to the formation of an ordered zirconium-oxygen phase of Zr3O, an immobilization of dislocations, and minimal plastic deformation in the cladding material.

Zircaloy cladding tube specimens from commercial power reactor fuel assemblies (burnup >22 MWd/kgU) have been deformed to fracture at 325°C by either the internal gas-pressurization or the expanding-mandrel technique in a helium or argon environment containing no fission product species (e.g., I, Cs, or Cd). The fracture surfaces of ten irradiated specimens fractured by internal gas pressurization were examined by scanning electron microscopy; six specimens were found to contain various degrees of the pseudocleavage feature that is characteristic of pellet-cladding interaction failures. Out of ten test specimens fractured by expanding-mandrel loading, five were found to contain regions of pseudocleavage on the fracture surfaces. The specimens exhibited "X-marks" on the outer surface and brittle incipient cracks distributed on the inner surface, which are also characteristic of pellet-cladding interaction failures. Transmission/high-voltage electron microscope examinations of the thin-foil specimens obtained from regions adjacent to the failure sites showed that the ductile-failure specimens were characterized by a high density of dislocations which showed normal ->?-type Burgers vectors. In contrast, the brittle-type specimens were characterized by comparatively few dislocations which formed substructures. The dislocations in the brittle specimens were decorated by Zr3O precipitates 2 to 6 nm in size, and cubic-ZrO2 precipitates ? 10 nm in size were also observed in high density. These observations indicate a general immobilization of the dislocations. The low-ductility brittle-type failures appear to have been produced primarily as a result of the Zr3O and cubic-ZrO2 precipitates, augmented by precipitates of bulk hydride 35 to 100 nm in size. The bulk nature of these precipitates, which contrasts with the surficial nature of monoclinic ZrO2 and ?-hydride precipitates, was indicated from stereomicroscopy of weak-beam dark-field images. In situ irradiation of the spent-fuel cladding specimens by 1-MeV electrons at 325°C indicates that the Zr3O and cubic-ZrO2 precipitation is irradiation-induced, whereas the bulk hydride is not.

Zircaloy cladding tube specimens from commercial power reactor fuel assemblies (burnup>22 MWd/kgU) have been deformed to fracture at 325°C by either the internal gas-pressurization or the expanding-mandrel technique in a helium or argon environment containing no fission product species (e.g., I, Cs, or Cd). The fracture surfaces of 11 irradiated specimens fractured by internal gas pressurization were examined by scanning electron microscopy, and 7 specimens were found to contain various degrees of the pseudocleavage feature that is characteristic of pellet-cladding interaction failures. Out of 10 test specimens fractured by expanding-mandrel loading, 5 were found to contain regions of pseudocleavage on the fracture surfaces. The specimens exhibited ''X-marks'' on the outer surface and brittle incipient cracks distributed on the inner surface, which are also characteristic of pellet-cladding interaction failures.