Flow meters measure the volumetric flow rate in a pipeline. Most meters are based on deriving a signal from the fluid flow and calibrating the signal against the volumetric flow rate. The calibration is done in fully-developed flow, and the same state of flow must exist at the meter’s position when it is in practical use. Because the field of flow metering has been neglected by fluid mechanicists for a long time, this book addresses two major fluid mechanical problems in flow metering: the analysis of signal generation in turbulent pipe flow, which explains the function of the meter beyond a simple calibration, and the possible use of a meter in non-developed flows. These problems are investigated with reference to, and examples from, a variety of meters, e.g. ultrasound cross-correlation meters, vortex meters, and turbine meters. Studying these problems requires consideration of specific phenomena in turbulent non-developed pipe flow, as caused by installations, and finding special solutions with signal processing, both of which are included in the book.

This revised edition provides updated fluid mechanics measurement techniques as well as a comprehensive review of flow properties required for research, development, and application. Fluid-mechanics measurements in wind tunnel studies, aeroacoustics, and turbulent mixing layers, the theory of fluid mechanics, the application of the laws of fluid mechanics to measurement techniques, techniques of thermal anemometry, laser velocimetry, volume flow measurement techniques, and fluid mechanics measurement in non-Newtonian fluids, and various other techniques are discussed.

There is a tendency to make flow measurement a highly theoretical and technical subject but what most influences quality measurement is the practical application of meters, metering principles, and metering equipment and the use of quality equipment that can continue to function through the years with proper maintenance have the most influence in obtaining quality measurement. This guide provides a review of basic laws and principles, an overview of physical characteristics and behavior of gases and liquids, and a look at the dynamics of flow. The authors examine applications of specific meters, readout and related devices, and proving systems. Practical guidelines for the meter in use, condition of the fluid, details of the entire metering system, installation and operation, and the timing and quality of maintenance are also included. This book is dedicated to condensing and sharing the authors' extensive experience in solving flow measurement problems with design engineers, operating personnel (from top supervisors to the newest testers), academically-based engineers, engineers of the manufacturers of flow meter equipment, worldwide practitioners, theorists, and people just getting into the business. - The authors' many years of experience are brought to bear in a thorough review of fluid flow measurement methods and applications - Avoids theory and focuses on presentation of practical data for the novice and veteran engineer - Useful for a wide range of engineers and technicians (as well as students) in a wide range of industries and applications

Flow meters measure the volumetric flow rate in a pipeline. Most meters are based on deriving a signal from the fluid flow and calibrating the signal against the volumetric flow rate. The calibration is done in fully-developed flow, and the same state of flow must exist at the meter’s position when it is in practical use. Because the field of flow metering has been neglected by fluid mechanicists for a long time, this book addresses two major fluid mechanical problems in flow metering: the analysis of signal generation in turbulent pipe flow, which explains the function of the meter beyond a simple calibration, and the possible use of a meter in non-developed flows. These problems are investigated with reference to, and examples from, a variety of meters, e.g. ultrasound cross-correlation meters, vortex meters, and turbine meters. Studying these problems requires consideration of specific phenomena in turbulent non-developed pipe flow, as caused by installations, and finding special solutions with signal processing, both of which are included in the book.

Covers a wide range of practical fluid mechanics, heat transfer, and mass transfer problems This book covers the many issues that occur in practical fluid mechanics, heat transfer, and mass transfer, and examines the basic laws (the conservation of matter, conservation of momentum, conservation of energy, and the second law of thermodynamics) of these areas. It offers problem solutions that start with simplifying engineering assumptions and then identifies the governing equations and dependent and independent variables. When solutions to basic equations are not possible, the book utilizes historical experimental studies. It also looks at determining appropriate thermo-physical properties of the fluid under investigation, and covers solutions to governing equations with experimental studies. Case Studies in Fluid Mechanics with Sensitivities to Governing Variables offers chapters on: draining fluid from a tank; vertical rise of a weather balloon; wind drag forces on people; Venturi meter; fluid’s surface shape in a rotating cylindrical tank; range of an aircraft; designing a water clock; water turbine under a dam; centrifugal separation of particles; ideal gas flow in nozzles and diffusers; water supply from a lake to a factory; convection mass transfer through air-water interface; heating a room by natural convection; condensation on the surface of a vertical plate in laminar flow regime; bubble rise in a glass of beer; and more. Covers a broad spectrum of problems in practical fluid mechanics, heat transfer, and mass transfer Examines the basic laws of fluid mechanics, heat transfer and mass transfer Presents solutions to governing equations with experimental studies Case Studies in Fluid Mechanics with Sensitivities to Governing Variables will appeal to engineers working in thermo-physical sciences and graduate students in mechanical engineering.

Study faster, learn better, and get top grades! Here is the ideal review for your fluid mechanics and hydraulics course More than 40 million students have trusted Schaum’s Outlines for their expert knowledge and helpful solved problems. Written by a renowned expert in this field, Schaum's Outline of Fluid Mechanics and Hydraulics covers what you need to know for your course and, more important, your exams. Step-by-step, the author walks you through coming up with solutions to exercises in this topic. Features: 622 fully solved problems Links to online instruction videos Practical examples of proofs of theorems and derivations of formulas Chapters on fluid statics and the flow of compressible fluids Detailed explanations of free-body analysis, vector diagrams, the principles of work and energy and impulse-momentum, and Newton’s laws of motion Helpful material for the following courses: Introduction to Fluid Dynamics; Introduction to Hydraulics; Fluid Mechanics; Statics and Mechanics of Materials

Practical, comprehensive advice on the design, operation, and performance of flowmeters.