The implementation of homogenous charge compression ignition (HCCI) to gasoline engines is constrained by many factors. This work examines constrains imposed by nitric oxide (NOx) emission and by the need to maintain a minimum catalyst temperature on HCCI operation. Then the nature of the approach to high load limit was examined for three fuels with very different behavior. An engine simulation was used to examine constrains imposed by NOx emission and by catalyst temperature requirement. The valve timing in a HCCI engine using NegativeValve-Overlap (NVO) was varied in the simulation to control the operating point. The engine speed and intake pressure (turbocharged mode) were varied. The High Load Limit (HLL) was attained when the NOx emission reached the regulated level for a Partial-Zero-Emissions-Vehicle (PZEV). This occurred when the engine was running at the lowest speed and the highest intake pressure. Unreasonably large residual fraction was required to achieve the NOx limit unless a three-way catalyst is used. The engine behavior in the operating trajectory to the HLL was examined by using two Primary Reference fuels (PRF60 and PRF90) and a fuel blended from refinery feed stock. The latter fuel had Extremely Low Aromatic and Olefin content and is referred to as the ELAO fuel. For PRF60 (the knock prone fuel), the Maximum Pressure Rise Rate (MPRR) increased with increase in load (by reduction of residual). The HLL was attained when the MPRR reached a pre-determined level of 5MPa/ms. For PRF90 (the knock resistant fuel), however, the MPRR decreased with increase in load, and the HLL was constrained by ignition failure. For the ELAO fuel, the MPRR first increased and then decreased with increase in load. The HLL was thus constrained by ignition failure. Thus depending on the fuel properties, there could be very different engine behaviors in the approach to the HLL of HCCI operation.

The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.

The homogeneous-charge compression-ignition (HCCI) engine is a novel engine technology with the potential to substantially lower emissions from automotive sources. HCCI engines use lean-premixed combustion to achieve good fuel economy and low emissions of nitrogen-oxides and particulate matter. However, experimentally these engines have demonstrated a viable operating range that is too narrow for vehicular applications. Incomplete combustion or misfire can occur under fuel-lean conditions imposing a minimum load at which the engine can operate. At high loads, HCCI engines are often extremely loud and measured cylinder pressures show strong acoustic oscillations resembling those for a knocking sparkignited engine. The goal of this research was to understand the factors limiting the HCCI range of operability and propose ways of broadening that range. An engine simulation tool was developed to model the combustion process in the engine and predict HCCI knock and incomplete combustion. Predicting HCCI engine knock is particularly important because knock limits the maximum engine torque, and this limitation is a major obstacle to commercialization. A fundamentally-based criterion was developed and shown to give good predictions of the experimental knock limit. Our engine simulation tool was then used to explore the effect of various engine design parameters and operating conditions on the HCCI viable operating range. Performance maps, which show the response of the engine during a normal driving cycle, were constructed to compare these engine designs. The simulations showed that an acceptably broad operating range can be achieved by using a low compression ratio, low octane fuel, and moderate boost pressure. An explanation of why this choice of parameters gives a broad operating window is discussed. Our prediction of the HCCI knock limit is based on the autoignition theory of knock, which asserts that local overpressures in the engine are caused by extremely rapid chemical energy release. A competing theory asserts that knock is caused by the formation of detonation waves initiated at autoignition centers ('hot-spots') in the engine. No conclusive experimental evidence exists for the detonation theory, but many numerical simulations in the literature show that detonation formation is possible; however, some of the assumptions made in these simulations warrant re-examination. In particular, the effect of curvature on small (quasispherical) hot-spots has often been overlooked. We first examined the well-studied case of gasoline spark-ignited engine knock and observed that the size of the hot-spot needed to initiate a detonation is larger than the end-gas region where knock occurs. Subsequent studies of HCCI engine knock predicted that detonations would not form regardless of the hot-spot size because of the low energy content of fuel-lean mixtures typically used in these engines. Our predictions of the HCCI viable operating range were shown to be quite sensitive to details of the ignition chemistry. Therefore, an attempt was made to build an improved chemistry model for HCCI combustion using automatic mechanism-generation software developed in our research group. Extensions to the software were made to allow chemistry model construction for engine conditions. Model predictions for n-heptane/air combustion were compared to literature data from a jet-stirred reactor and rapid-compression machine. We conclude that automatic mechanism generation gives fair predictions without the tuning of rate parameters or other efforts to improve agreement. However, some tuning of the automatically-generated chemistry models is necessary to give the accurate predictions of HCCI combustion needed for our design calculations.

Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.

While the potential emissions and efficiency benefits of homogeneous charge compression ignition (HCCI) combustion are well known, realizing the potentials on a production intent engine presents numerous challenges. In this study we focus on characterizing the authority of the available engine controls as the high load limit of HCCI combustion is approached. The experimental work is performed on a boosted single-cylinder research engine equipped with direct injection (DI) fueling, cooled external exhaust gas recirculation (EGR), and a hydraulic valve actuation (HVA) valve train to enable the negative valve overlap (NVO) breathing strategy. Valve lift and duration are held constant while phasing is varied in an effort to make the results as relevant as possible to production intent cam-based variable valve actuation (VVA) systems on multi-cylinder engines. Results presented include engine loads from 350 to 650 kPa IMEPnet and manifold pressure from 98 to 190 kPaa at 2000 rpm. It is found that in order to increase engine load to 650 kPa IMEPnet, it is necessary to increase manifold pressure and external EGR while reducing the NVO duration. Both NVO duration and fuel injection timing are effective means of controlling combustion phasing, with NVO duration being a coarse control and fuel injection timing being a fine control. NOX emissions are low throughout the study, with emissions below 0.1 g/kW-h at all boosted HCCI conditions, while good combustion efficiency is maintained (>96.5%). Net indicated thermal efficiency increases with load up to 600 kPa IMEPnet, where a peak efficiency of 41% is achieved. Results of independent parametric investigations are presented on the effect of external EGR, intake effect of manifold pressure, and the effect of NVO duration. It is found that increasing EGR at a constant manifold pressure and increasing manifold pressure at a constant EGR rate both have the effect of retarding combustion phasing. It is also found that combustion phasing becomes increasingly sensitive to NVO duration as engine load increases. Finally, comparisons are made between three commonly used noise metrics (AVL noise meter, ringing intensity (RI), and maximum pressure rise rate (MPRR)). It is found that compared to the AVL noise meter, RI significantly underestimates combustion noise under boosted conditions.

Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality.HCCI and CAI engines for the automotive industry presents the state-of-the-art in research and development on an international basis, as a one-stop reference work. The background to the development of HCCI / CAI engine technology is described. Basic principles, the technologies and their potential applications, strengths and weaknesses, as well as likely future trends and sources of further information are reviewed in the areas of gasoline HCCI / CAI engines; diesel HCCI engines; HCCI / CAI engines with alternative fuels; and advanced modelling and experimental techniques. The book provides an invaluable source of information for scientific researchers, R&D engineers and managers in the automotive engineering industry worldwide. - Presents the state-of-the-art in research and development on an international basis - An invaluable source of information for scientific researchers, R&D engineers and managers in the automotive engineering industry worldwide - Looks at one of the most promising engine technologies around