Design and Analysis of High Efficiency Line Drivers for xDSL covers the most important building block of an xDSL (ADSL, VDSL, ...) system: the line driver. Traditional Class AB line drivers consume more than 70% of the total power budget of state-of-the-art ADSL modems. This book describes the main difficulties in designing line drivers for xDSL. The most important specifications are elaborated staring from the main properties of the channel and the signal properties. The traditional (class AB), state-of-the-art (class G) and future technologies (class K) are discussed. The main part of Design and Analysis of High Efficiency Line Drivers for xDSL describes the design of a novel architecture: the Self-Oscillating Power Amplifier or SOPA.

This book fits in the quest for highly efficient fully integrated xDSL modems for central office applications. It presents a summary of research at one of Europe’s most famous analog design research groups over a five year period. The book focuses on the line driver, the most demanding building block of the xDSL modem for lowering power. The book covers the total design flow of monolithic CMOS high voltage circuits. It is essential reading for analog design engineers.

Thanks to the advance of semiconductor and communication technology, the wireless communication market has been booming in the last two decades. It evolved from simple pagers to emerging third-generation (3G) cellular phones. In the meanwhile, broadband communication market has also gained a rapid growth. As the market always demands hi- performance and low-cost products, circuit designers are seeking hi- integration communication devices in cheap CMOS technology. The phase-locked loop frequency synthesizer is a critical component in communication devices. It works as a local oscillator for frequency translation and channel selection in wireless transceivers and broadband cable tuners. It also plays an important role as the clock synthesizer for data converters in the analog-and-digital signal interface. This book covers the design and analysis of PLL synthesizers. It includes both fundamentals and a review of the state-of-the-art techniques. The transient analysis of the third-order charge-pump PLL reveals its locking behavior accurately. The behavioral-level simulation of PLL further clarifies its stability limit. Design examples are given to clearly illustrate the design procedure of PLL synthesizers. A complete derivation of reference spurs in the charge-pump PLL is also presented in this book. The in-depth investigation of the digital CA modulator for fractional-N synthesizers provides insightful design guidelines for this important block.

To meet the demands of today's highly competitive market, analog electronics designers must develop their IC designs in a minimum of time. The difference between first- and second-time right seriously affects a company's share of the market. Analog designers are therefore in need for structured design methods together with the theory and tools to support them, especially when pushing the performance limits in high-performance designs. Systematic Modeling and Analysis of Telecom Frontends and Their Building Blocks aims to help designers in speeding up telecommunication frontend design by offering an in-depth understanding of the frontend's behavior together with methods and algorithms that support designers in bringing this understanding to practice. The book treats topics such as time-varying phase-locked loop stability, noise in mixing circuits, oscillator injection locking, oscillator phase noise behavior, harmonic oscillator dynamics and many more. In doing so, it always starts from a theoretical foundation that is both rigorous and general. Phase-locked loop and mixer analysis, for example, are grounded upon a general framework for time-varying small-signal analysis. Likewise, analysis of harmonic oscillator transient behavior and oscillator phase noise analysis are treated as particular applications of a general framework for oscillator perturbation analysis. In order to make the book as easy to read as possible, all theory is always accompanied by numerous examples and easy-to-catch intuitive explanations. As such, the book is suited for both computer-aided design engineers looking for general theories and methods, either as background material or for practical implementation in tools, as well as for practicing circuit designers looking for help and insight in dealing with a particular application or a particular high-performance design problem.

Design of Very High-Frequency Multirate Switched-Capacitor Circuits presents the theory and the corresponding CMOS implementation of the novel multirate sampled-data analog interpolation technique which has its great potential on very high-frequency analog frond-end filtering due to its inherent dual advantage of reducing the speed of data-converters and DSP core together with the specification relaxation of the post continuous-time filtering. This technique completely eliminates the traditional phenomenon of sampled-and-hold frequency-shaping at the lower input sampling rate. Also, in order to tackle physical IC imperfections at very high frequency, the state-of-the-art circuit design and layout techniques for high-speed Switched-Capacitor (SC) circuits are comprehensively discussed: -Optimum circuit architecture tradeoff analysis -Simple speed and power trade-off analysis of active elements -High-order filtering response accuracy with respect to capacitor-ratio mismatches -Time-interleaved effect with respect to gain and offset mismatch -Time-interleaved effect with respect to timing-skew and random jitter with non-uniformly holding -Stage noise analysis and allocation scheme -Substrate and supply noise reduction -Gain-and offset-compensation techniques -High-bandwidth low-power amplifier design and layout -Very low timing-skew multiphase generation Two tailor-made optimum design examples in CMOS are presented. The first one achieves a 3-stage 8-fold SC interpolating filter with 5.5MHz bandwidth and 108MHz output sampling rate for a NTSC/PAL CCIR 601 digital video at 3 V. Another is a 15-tap 57MHz SC FIR bandpass interpolating filter with 4-fold sampling rate increase to 320MHz and the first-time embedded frequency band up-translation for DDFS system at 2.5V. The corresponding chip prototype achieves so far the highest operating frequency, highest filter order and highest center frequency with highest dynamic range under the lowest supply voltage when compared to the previously reported high-frequency SC filters in CMOS.

High-speed Photodiodes in Standard CMOS Technology describes high-speed photodiodes in standard CMOS technology which allow monolithic integration of optical receivers for short-haul communication. For short haul communication the cost aspect is important , and therefore it is desirable that the optical receiver can be integrated in the same CMOS technology as the rest of the system. If this is possible then ultimately a singe-chip system including optical inputs becomes feasible, eliminating EMC and crosstalk problems, while data rate can be extremely high. The problem of photodiodes in standard CMOS technology it that they have very limited bandwidth, allowing data rates up to only 50Mbit per second. High-speed Photodiodes in Standard CMOS Technology first analyzes the photodiode behaviour and compares existing solutions to enhance the speed. After this, the book introduces a new and robust electronic equalizer technique that makes data rates of 3Gb/s possible, without changing the manufacturing technology. The application of this technique can be found in short haul fibre communication, optical printed circuit boards, but also photodiodes for laser disks.

Systematic Design of Sigma-Delta Analog-to-Digital Converters describes the issues related to the sigma-delta analog-to-digital converters (ADCs) design in a systematic manner: from the top level of abstraction represented by the filters defining signal and noise transfer functions (STF, NTF), passing through the architecture level where topology-related performance is calculated and simulated, and finally down to parameters of circuit elements like resistors, capacitors, and amplifier transconductances used in individual integrators. The systematic approach allows the evaluation of different loop filters (order, aggressiveness, discrete-time or continuous-time implementation) with quantizers varying in resolution. Topologies explored range from simple single loops to multiple cascaded loops with complex structures including more feedbacks and feedforwards. For differential circuits, with switched-capacitor integrators for discrete-time (DT) loop filters and active-RC for continuous-time (CT) ones, the passive integrator components are calculated and the power consumption is estimated, based on top-level requirements like harmonic distortion and noise budget. This unified, systematic approach to choosing the best sigma-delta ADC implementation for a given design target yields an interesting solution for a high-resolution, broadband (DSL-like) ADC operated at low oversampling ratio, which is detailed down to transistor-level schematics. The target audience of Systematic Design of Sigma-Delta Analog-to-Digital Converters are engineers designing sigma-delta ADCs and/or switched-capacitor and continuous-time filters, both beginners and experienced. It is also intended for students/academics involved in sigma-delta and analog CAD research.