This is the fourth volume in the well-established series of compendiums devoted to the subject of weld hot cracking. It contains the papers presented at the 4th International Cracking Workshop held in Berlin in April 2014. In the context of this workshop, the term “cracking” refers to hot cracking in the classical and previous sense, but also to cold cracking, stress-corrosion cracking and elevated temp. solid-state cracking. A variety of different cracking subjects are discussed, including test standards, crack prediction, weldability determination, crack mitigation, stress states, numerical modelling, and cracking mechanisms. Likewise, many different alloys were investigated such as aluminum alloys, copper-aluminum dissimilar metal, austenitic stainless steel, nickel base alloys, duplex stainless steel, creep resistant steel, and high strength steel.

This is the fourth volume in the well-established series of compendiums devoted to the subject of weld hot cracking. It contains the papers presented at the 4th International Hot Cracking Workshop held in Berlin in April 2014. In the context of this workshop, the term "hot cracking" refers to elevated temperature cracking associated with either the weld metal or heat-affected zone. These hot cracking phenomena include weld solidification cracking, HAZ and weld metal liquation cracking, and ductility-dip cracking. The book is divided into three major sections based on material type; specifically aluminum alloys, steels, and nickel-base alloys.

Hot cracking in welds still has not been fully understood. Hot Cracking Phenomena in Welds contains 20 individual contributions from experts all over the world. The book provides the latest insight on hot cracking phenomena in welds and gives a comprehensive overview of the state of knowledge in this subject, addressing engineers and scientists in research and development. It contains numerous solutions and helpful guidance on specific problems, particularly for welding engineers confronted with hot cracking in practice. The book touches all three types of hot cracking, namely solidification cracking, liquation cracking and ductility dip cracking. It explains the differences of the mechanisms,thus representing also a very helpful tool for metallurgists and advanced engineering students. TOC:Phenomena and Mechanisms.- Metallurgy and Materials.- Modelling and Simulation.- Testing and Standardisation.

Failure of welded components can occur during service as well as during fabrication. Most common, analyses of the resistance of welded components against failure are targeted at crack avoidance. Such evaluations are increasingly carried out by modern weldability studies, i. e. considering interactions between the selected base and filler materials, structural design and welding process. Such weldability investigations are particularly targeted to prevent hot cracking, as one of the most common cracking phenomena occurring during weld fabrication. To provide an international information and discussion platform to combat hot cracking, an international workshop on Hot Cracking Phenomena in Welds has been created, based on an initiative of the Institute for Materials and Joining Technology at the Otto-von-Guericke University in Magdeburg and the Division V. 5 – Safety of Joined Components at the Federal Institute for Materials Research and Testing (BAM) in Berlin, Germany. The first workshop was organized in Berlin under the topics mechanisms and phenomena, metallurgy and materials, modelling and simulations as well as testing and standardization. It consisted of 20 individual contributions from eight countries, which were compiled in a book that found a very ready market, not only in the welding community. As a consequence of increasing interest, it has been decided to establish the Workshop on Hot Cracking Phenomena in Welds as a regular event every three years embedded in the International Institute of Welding (IIW). Attached to the IIW Commission IX and II Spring intermediate meetings, the second workshop was organized in March 2007.

This is the third in a series of compendiums devoted to the subject of weld hot cracking. It contains 22 papers presented at the 3rd International Hot Cracking Workshop in Columbus, Ohio USA in March 2010. In the context of this workshop, the term “hot cracking” refers to elevated temperature cracking associated with either the weld metal or heat-affected zone. These hot cracking phenomena include weld solidification cracking, HAZ and weld metal liquation cracking, and ductility-dip cracking. The book is divided into three major sections based on material type; specifically aluminum alloys, steels, and nickel-base alloys. Each of these sections begins with a keynote paper from prominent researchers in the field: Dr. Sindo Kou from the University of Wisconsin, Dr. Thomas Böllinghaus from BAM and the University of Magdeburg, and Dr. John DuPont from Lehigh University. The papers contained within include the latest insight into the mechanisms associated with hot cracking in these materials and methods to prevent cracking through material selection, process modification, or other means. The three Hot Cracking Phenomena in Welds compendiums combined contain a total of 64 papers and represent the best collection of papers on the topic of hot cracking ever assembled.

This resource covers all areas of interest for the practicing engineer as well as for the student at various levels and educational institutions. It features the work of authors from all over the world who have contributed their expertise and support the globally working engineer in finding a solution for today‘s mechanical engineering problems. Each subject is discussed in detail and supported by numerous figures and tables.

International Conference on Recent Advances in Materials and Manufacturing Technologies (ICRAMMT 2018) Selected, peer reviewed papers from the 2nd International Conference on Recent Advances in Materials and Manufacturing Technologies (ICRAMMT-2018), November 19-20, 2018, Hyderabad, India