Introductory technical guidance for civil engineers, structural engineers and construction managers interested in structural stability of flood walls. Here is what is discussed: 1. SCOPE, 2. REPRESENTATIVE LOADING CONDITIONS, 3. RETAINING WALLS, 4. INLAND FLOOD WALLS, 5. COASTAL FLOOD WALLS, 6. STABILITY CONSIDERATIONS, 7. STABILITY CRITERIA, 8. OVERTURNING STABILITY, 9. OVERTURNING STABILITY CRITERIA, 10. OVERVIEW OF SLIDING STABILITY ANALYSIS, 11. SLIDING FACTOR OF SAFETY, 12. ASSUMPTIONS AND SIMPLIFICATIONS, 13. GENERAL WEDGE EQUATION, 14. SLIP-PLANE ANGLE, 15. SINGLE WEDGE ANALYSIS, 16. MULTIPLE WEDGE ANALYSIS, 17. SLIDING STABILITY CRITERIA, 18. DESIGN CONSIDERATIONS, 19. BEARING CAPACITY ANALYSIS, 20. SUMMARY OF DESIGN PROCEDURES.

Introductory technical guidance for civil and geotechnical engineers nd construction managers interested in design, engineering and construction of flood and retaining walls. Here is what is discussed: 1. ALTERNATE TYPES OF RETAINING WALLS 2. DESIGN AND CONSTRUCTION DETAILS AND CAUSES OF UNSATISFACTORY PERFORMANCE OF FLOOD WALLS 3. FORCES ON FLOOD WALLS DUE TO EARTH PRESSURE 4. FLOOD WALL FOUNDATION ANALYSIS 5. GENERAL CONSIDERATIONS FOR FLOOD AND RETAINING WALLS 6. GRAVITY AND CANTILEVER FLOOD WALLS 7. SPECIAL CONSIDERATIONS FOR FLOOD WALLS 8. STRUCTURAL STABILITY OF FLOOD WALLS 9. WATER FORCES ON FLOOD WALLS..

Introductory technical guidance for civil, structural and geotechnical engineers and construction managers interested in stability requirements and loads for concrete structures.

Introductory technical guidance for civil, geotechnical and structural engineers interested in stabilization of existing, massive concrete structures such as dams, locks and flood walls. Here is what is discussed: 1. EVALUATION 2. PROCEDURES 3. IMPROVING STABILITY 4. CASE HISTORIES 5. ANCHORING STRUCTURES 6. ANCHORING STRUCTURES TO ROCK 7. TENSIONED ANCHOR LOADS 8. STRUCTURAL ANCHOR DESIGN 9. CLASSIFICATION OF STRUCTURES.

Introductory technical guidance for civil engineers, structural engineers and construction managers interested in stability requirements and loads for concrete structures. Here is what is discussed: 1. STABILITY REQUIREMENTS, 2. LOADS AND LOADING CONDITIONS, 3. STRESS METER FOR CONCRETE, 4.. PORE PRESSURE CELL, 5. THE REINFORCED CONCRETE METER.

Introductory technical guidance for civil and geotechnical engineers interested in flood wall design and engineering. Here is what is discussed: 1. GENERAL CHARACTERISTICS 2. RATIONALE FOR LOADING CASES 3. GENERAL CONSIDERATIONS 4. UNDERSEEPAGE CONTROL 5. FOUNDATION BASE TYPES 6. HORIZONTAL WATER AND EARTH LOADS ON KEYS 7. UNSUITABLE FOUNDATION MATERIAL AND BANK STABILITY 8. SCOUR PROTECTION 9. CHANGE-OF-ALIGNMENT MONOLITHS 10. CLOSURE AND ABUTMENT MONOLITHS 11. DRAINAGE STRUCTURE MONOLITHS 12. TRANSITION SECTIONS BETWEEN FLOOD WALLS AND LEVEES 13. WATER STOPS 14. CONTRACTION AND EXPANSION JOINTS 15. ADJACENT STRUCTURES AND RIGHTS-OF-WAY 16. ARCHITECTURAL AND LANDSCAPING CONSIDERATIONS 17. INSTRUMENTATION CONSIDERATIONS 18. TYPES OF INSTRUMENTATION 19. OPERATION AND MAINTENANCE MANUAL REQUIREMENTS 20. INSPECTION 21. REPAIR MEASURES.

Introductory technical guidance for civil, structural and geotechnical engineers interested in stability of large concrete structures such as dams and locks. Here is what is discussed: 1. FAILURE MODES AND WEDGE SLIDING ANALYSIS 2. STABILITY REQUIREMENTS 3. RISK-BASED ANALYSIS FOR FLOOD PROJECT STUDIES 4. SITE INFORMATION 5. CRITICAL STRUCTURES 6. EXISTING STRUCTURES 7. FACTORS OF SAFETY FOR SLIDING 8. FACTORS OF SAFETY FOR FLOTATION 9. LIMITS ON RESULTANT LOCATION 10. ALLOWABLE BEARING CAPACITY 11. SEISMIC STABILITY 12. MANDATORY REQUIREMENTS.