Gear cracks are typically difficult to diagnose with sufficient warning time. Significant damage must he present before algorithms detect the damage. A new feature extraction and two new detection techniques are proposed. The time synchronous averaging concept was extended from revolution-based to tooth engagement-based. The detection techniques are based on statistical comparisons among the averages for the individual teeth. These techniques were applied to a series of three seeded fault crack propagation tests. These tests were conducted on aerospace quality spur gears in a test rig. The tests were conducted at speeds ranging from 2500 to 7500 revolutions per minute and torque from 184 to 228 percent of design load. The inability to detect these cracks with high confidence may be caused by the high loading required to initiate the cracks. The results indicate that these techniques do not currently produce an indication of damage that significantly exceeds experimental scatter.

Health and Usage Monitoring System research and development involves analysis of the vibration signals produced by a gearbox throughout its life. There are two major advantages of knowing the actual lifetime of a gearbox component: safety and cost. In this report, a technique is proposed to help extract the critical data and present it in a manner that can be easy to understand. The key feature of the technique is to make it independent of speed, torque and prior history for localized, single tooth damage such as gear cracks. This extraction technique is demonstrated on two sets of digitized vibration data from cracked spur gears. Standard vibration diagnostic parameters are calculated and presented for comparison. Several new detection algorithms are also presented. The results of this study indicate that crack detection methods examined are not robust or repeatable. The proposed techniques provide a limited improvement to existing diagnostic parameters. Current techniques show that the cracks progressed at a much faster rate than anticipated which reduced available time for detection.

This book gathers contributions presented at the 9th Workshop on Cyclostationary Systems and Their Applications, held in Gródek nad Dunajcem, Poland in February 2016. It includes both theory-oriented and practice-oriented chapters. The former focus on heavy-tailed time series and processes, PAR models, rational spectra for PARMA processes, covariance invariant analysis, change point problems, and subsampling for time series, as well as the fraction-of-time approach, GARMA models and weak dependence. In turn, the latter report on case studies of various mechanical systems, and on stochastic and statistical methods, especially in the context of damage detection. The book provides students, researchers and professionals with a timely guide to cyclostationary systems, nonstationary processes and relevant engineering applications.

The first book on Prognostics and Health Management of Electronics Recently, the field of prognostics for electronic products has received increased attention due to the potential to provide early warning of system failures, forecast maintenance as needed, and reduce life cycle costs. In response to the subject's growing interest among industry, government, and academic professionals, this book provides a road map to the current challenges and opportunities for research and development in Prognostics and Health Management (PHM). The book begins with a review of PHM and the techniques being developed to enable a prognostics approach for electronic products and systems. building on this foundation, the book then presents the state of the art in sensor systems for in-situ health and usage monitoring. Next, it discusses the various models and algorithms that can be utilized in PHM. Finally, it concludes with a discussion of the opportunities in future research. Readers can use the information in this book to: Detect and isolate faults Reduce the occurrence of No Fault Found (NFF) Provide advanced warning of system failures Enable condition-based (predictive) maintenance Obtain knowledge of load history for future design, qualification, and root cause analysis Increase system availability through an extension of maintenance cycles and/or timely repair actions Subtract life cycle costs of equipment from reduction in inspection costs, down time, and inventory Prognostics and Health Management of Electronics is an indispensable reference for electrical engineers in manufacturing, systems maintenance, and management, as well as design engineers in all areas of electronics.

An existing technique for the signal processing to the time domain average of the tooth meshing vibration of gears is examined with application to the early detection of failure. It is shown that the regular signal extracted from the time domain average of the gear vibration by the elimination of the fundamental and harmonics of the tooth meshing frequency forms the time domain average of the vibration of a single tooth. The residual signal which is obtained by subtracting the regular signal from the original time domain average gives the departures of the vibration from the average. Numerical and practical examples are given. (Author).

This essential text contains the papers from the 8th international IMechE conference on Vibrations in Rotating Machinery held at the University of Wales, Swansea in September 2004. The themes of the volume are new developments and industrial applications of current technology relevant to the vibration and noise of rotating machines and assemblies. TOPICS INCLUDE Rotor balancing – including active and automatic balancing Special rotating machines – including micromachines Oil film bearings and dampers Active control methods for rotating machines Smart machine technology Dynamics of assembled rotors Component life predictions and life extension strategies The dynamics of geared systems Cracked rotors – detection, location ad prognosis Chaotic behaviour in machines Experimental methods and discoveries.

Explores the detailed steps necessary to determine the causes of failure. First, the physical characteristics of a gear are studied: where the stress points are, from what directions the forces are applied, where the movement of material progresses, and where strain patterns exist. Second, all external conditions and forces are considered. With this background information, a systematic examination is described from beginning to end, the end being a conclusion about the mode and cause of failure.