Health and Usage Monitoring System research and development involves analysis of the vibration signals produced by a gearbox throughout its life. There are two major advantages of knowing the actual lifetime of a gearbox component: safety and cost. In this report, a technique is proposed to help extract the critical data and present it in a manner that can be easy to understand. The key feature of the technique is to make it independent of speed, torque and prior history for localized, single tooth damage such as gear cracks. This extraction technique is demonstrated on two sets of digitized vibration data from cracked spur gears. Standard vibration diagnostic parameters are calculated and presented for comparison. Several new detection algorithms are also presented. The results of this study indicate that crack detection methods examined are not robust or repeatable. The proposed techniques provide a limited improvement to existing diagnostic parameters. Current techniques show that the cracks progressed at a much faster rate than anticipated which reduced available time for detection.

Health and Usage Monitoring System research and development involves analysis of the vibration signals produced by a gearbox throughout its life. There are two major advantages of knowing the actual lifetime of a gearbox component: safety and cost. In this report, a technique is proposed to help extract the critical data and present it in a manner that can be easy to understand. The key feature of the technique is to make it independent of speed, torque and prior history for localized, single tooth damage such as gear cracks. This extraction technique is demonstrated on two sets of digitized vibration data from cracked spur gears. Standard vibration diagnostic parameters are calculated and presented for comparison. Several new detection algorithms are also presented. The results of this study indicate that crack detection methods examined are not robust or repeatable. The proposed techniques provide a limited improvement to existing diagnostic parameters. Current techniques show that the cracks progressed at a much faster rate than anticipated which reduced available time for detection. Decker, Harry J. Glenn Research Center NASA/TM-2002-211492, NAS 1.15:211492, E-13260, ARL-TR-2682

Gear cracks are typically difficult to diagnose with sufficient warning time. Significant damage must he present before algorithms detect the damage. A new feature extraction and two new detection techniques are proposed. The time synchronous averaging concept was extended from revolution-based to tooth engagement-based. The detection techniques are based on statistical comparisons among the averages for the individual teeth. These techniques were applied to a series of three seeded fault crack propagation tests. These tests were conducted on aerospace quality spur gears in a test rig. The tests were conducted at speeds ranging from 2500 to 7500 revolutions per minute and torque from 184 to 228 percent of design load. The inability to detect these cracks with high confidence may be caused by the high loading required to initiate the cracks. The results indicate that these techniques do not currently produce an indication of damage that significantly exceeds experimental scatter.

The first book on Prognostics and Health Management of Electronics Recently, the field of prognostics for electronic products has received increased attention due to the potential to provide early warning of system failures, forecast maintenance as needed, and reduce life cycle costs. In response to the subject's growing interest among industry, government, and academic professionals, this book provides a road map to the current challenges and opportunities for research and development in Prognostics and Health Management (PHM). The book begins with a review of PHM and the techniques being developed to enable a prognostics approach for electronic products and systems. building on this foundation, the book then presents the state of the art in sensor systems for in-situ health and usage monitoring. Next, it discusses the various models and algorithms that can be utilized in PHM. Finally, it concludes with a discussion of the opportunities in future research. Readers can use the information in this book to: Detect and isolate faults Reduce the occurrence of No Fault Found (NFF) Provide advanced warning of system failures Enable condition-based (predictive) maintenance Obtain knowledge of load history for future design, qualification, and root cause analysis Increase system availability through an extension of maintenance cycles and/or timely repair actions Subtract life cycle costs of equipment from reduction in inspection costs, down time, and inventory Prognostics and Health Management of Electronics is an indispensable reference for electrical engineers in manufacturing, systems maintenance, and management, as well as design engineers in all areas of electronics.

Containing selected papers from the ICRESH-ARMS 2015 conference in Lulea, Sweden, collected by editors with years of experiences in Reliability and maintenance modeling, risk assessment, and asset management, this work maximizes reader insights into the current trends in Reliability, Availability, Maintainability and Safety (RAMS) and Risk Management. Featuring a comprehensive analysis of the significance of the role of RAMS and Risk Management in the decision making process during the various phases of design, operation, maintenance, asset management and productivity in Industrial domains, these proceedings discuss key issues and challenges in the operation, maintenance and risk management of complex engineering systems and will serve as a valuable resource for those in the field.

Gear cracks are typically difficult to diagnose with sufficient time before catastrophic damage occurs. Significant damage must be present before algorithms appear to be able to detect the damage. Frequently there are multiple gear meshes on a single shaft. Since they are all synchronous with the shaft frequency, the commonly used synchronous averaging technique is ineffective in removing other gear mesh effects. Carefully applying a filter to these extraneous gear mesh frequencies can reduce the overall vibration signal and increase the accuracy of commonly used vibration metrics. The vibration signals from three seeded fault tests were analyzed using this filtering procedure. Both the filtered and unfiltered vibration signals were then analyzed using commonly used fault detection metrics and compared. The tests were conducted on aerospace quality spur gears in a test rig. The tests were conducted at speeds ranging from 2500 to 5000 revolutions per minute and torques from 184 to 228 percent of design load. The inability to detect these cracks with high confidence results from the high loading which is causing fast fracture as opposed to stable crack growth. The results indicate that these techniques do not currently produce an indication of damage that significantly exceeds experimental scatter.

Sensors & Instrumentation and Aircraft/Aerospace Testing Techniques, Volume 8: Proceedings of the 41st IMAC, A Conference and Exposition on Structural Dynamics, 2023, the eighth volume of ten from the Conference brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on fundamental and applied aspects of Shock & Vibration, Aircraft/Aerospace Testing Techniques including papers on: Alternative Sensing & Acquisition Active Controls Instrumentation